how to install brostrend ac1200 driver Archives

Setup Brostrend AC1200

How to Setup Brostrend AC1200 WIFI extender?

Post category:Bros Trend Extender Setup
Post comments:0 Comments

The BrosTrend AC1200 is a wireless range extender that helps to increase the Wi-Fi coverage in your home or office. It works by receiving your existing Wi-Fi signal and then amplifying it to cover a wider area. The BrosTrend AC1200 WIFI extender supports two modes of setup: WPS setup and web-based setup using Re.brostrend.com. In this guide, we will provide you with step-by-step instructions on how to set up the BrosTrend AC1200 WIFI extender using both methods.

Step-by-step Setup Brostrend AC1200 using WPS:

First, make sure that your BrosTrend AC1200 WIFI extender is plugged into a power outlet and is within range of your existing Wi-Fi network.
Press the WPS button on your router and hold it for 2-3 seconds.
Within two minutes, press the WPS button on the BrosTrend AC1200 WIFI extender and hold it for 2-3 seconds.
Once the WPS LED on the BrosTrend AC1200 WIFI extender starts flashing, the extender will automatically connect to your existing Wi-Fi network.
After the connection is established, the WPS LED on the BrosTrend AC1200 WIFI extender will turn solid and you can start using your extended Wi-Fi network.

Setup Brostrend Extender using Re.brostrend.com:

First, make sure that your BrosTrend AC1200 WIFI extender is plugged into a power outlet and is within range of your existing Wi-Fi network.
Connect your computer or smartphone to the Wi-Fi network of the BrosTrend AC1200 WIFI extender.
Open your web browser and go to the web-based setup page by typing “Re.brostrend.com” or “192.168.1.1” in the address bar.
On the login page, enter “admin” as the username and “admin” as the password, and click on the “Login” button.
Select the “Wireless Repeater” mode on the setup page and click on the “Next” button.
The BrosTrend AC1200 WIFI extender will then scan for available Wi-Fi networks. Select your existing Wi-Fi network from the list and enter the password.
Click on the “Next” button and then the “Finish” button to complete the setup process.
Wait for a few minutes for the BrosTrend AC1200 WIFI extender to connect to your existing Wi-Fi network.
Once the connection is established, you can start using your extended Wi-Fi network.

In this guide, we have provided you with step-by-step instructions on how to set up the BrosTrend AC1200 WIFI extender using WPS and Re.brostrend.com. Both methods are easy to follow and should take only a few minutes to complete. By extending your Wi-Fi coverage, you can enjoy better connectivity throughout your home or office.

Bros Trend AC750 Extender Setup

Post category:Bros Trend Extender Setup
Post comments:0 Comments

Bros Trend AC750 extender Setup is also referred as RSD0607 Extender. It is a wireless Wi-Fi extender that assists in eliminating dead spots at your workplace. It can simply connect the extender with the existing network. It contains of numerous features that make this extender different.

Here are some characteristics of extender are follows:-

Permanent Signal Connection.
Complete Signal Coverage.
Compatible with every sort of router.

With the help of the smart signal indicator you can locate a definite spot. You should associate the extender through Graphical User Interface (GUI) or WPS connection. Bros Trends wireless extender help the dual-band technology that is 2 GHz to 5 GHz. It also has a warranty. Let’s begin the Bros Trends Extender setup:

Firstly setup Bros Trend AC750 Extender is to power it via an electrical AC outlet.
Secondly, associate your extender to the closest power AC outlet.
Associate your Wi-Fi device to extender’s Wi-Fi network and ensure that mobile data of your device should not be turned on.
After this, open any internet browser on your device and enter the URL https://re-brostrend.com/ in the address bar or type 192.168.0.254.
Then, create the login username and password.
Enter the Wi-Fi password and hold up until the extender starts displaying.
Once the Setup RSD0607 Bros Trend Extender completed then relocates the extender in between the router and dead spots.

Moreover, when it spots the coverage you will get to know about it via an LED indicator which will turn blue

Bros Trend AC750 Extender setup via WPS

Firstly to Setup Bros trend AC750 Extender , you have to plugin into any electrical socket which is closer to the router.
LED starts lighting blue then you can begin with the setup procedure.
After that, the LED indicator starts lightning press the WPS button of the router.
In around two minutes of pressing the WPS button of the router press the WPS button of Extender as well and check if the LED signal turns blue or red.
Then, Relocate the Bros Trend extender in between the router and dead spot and check the coverage strength with an LED indicator.
At last, you will get the complete coverage strength then you can freely use your network without any interference.

Bros Trend AC750 RSD0607 extender as an Access Point

Firstly, you have to plug into the electrical power outlet Setup AC750 Bros trend Extender.
Secondly, connect your router and extender via good quality Ethernet cable.
Open the web page and visit 192.168.0.254 or type the URL https://re-brostrend.com/ and from the menu choose the option mode.
At last, set up an SSID and Password.

Features of Bros Trend AC750 extender

Bros Trend AC750 extender has numerous new features which make it different and compatible as mentioned underneath:

It has Steady signal connection with dual-band technology
It is Compatible with every router.
Contains of dual antennas which raises signal coverage.
It can be simply set up through the WPS button or web user interface.
Smart signal LED indicator that help in finding accurate spots.

Setup Brostrend Mesh WiFi System

Post category:Bros Trend Extender
Post comments:0 Comments

This article is about “Setup Brostrend Mesh Wi-Fi system” The customary routers, Brostrend Home WiFi System design an MU-MIMO Wi-Fi. Also has concurrent dual-band 2.4GHz & 5GHz and provide speed up to 1167Mbps. At a same rate and time it can transfer the data to multiple devices. For gaming experience you can enable smart QoS functions.

Setup the primary mesh node

The first node you set up functions as the essential node, while the rest areas the secondary nodes. If it’s not too much trouble power on one Mesh first connects the other Mesh after you set the first Mesh to the internet on the Apps.

First, make sure to turn off your modem and exile its battery.
Then with Ethernet cable connect a LAN port of your modem. This node is the primary node.
Now reinsert the battery and turn on your modem.
Further with the connector to connect the basic node to power source, here you will see LED turns to green and shine rapidly.
Now wait for about 40 seconds to complete the setup till the LED turn to green slowly.

Setup Brostrend Mesh WiFi System — Brostrend Mesh WiFi

Connect the primary node to the internet

Firstly, visit to Wi-Fi network list from your device and select your SSID and enter its password.
Here SSID and password are set on the bottom label of node.
Now open the wifi App and stick to on screen instructions to address the essential node to web.

Once the essential node is connected with web, you will see the LED turns to solid green.

Setup the first Brostrend mesh node on App

First open the Wi-Fi app and then setup wizard displays, click on “setup”.
Here recognizes your web association and enter data as instructed by web association type and click to “Next”.
Then work unit is connected with web and the app continues to following stage.
In case your Internet connection type is PPPoE, then enter your PPPoE user name and password and click “Next”.
In case your web connection type is dynamic IP, click “Next”.
Now set mesh unit wireless network name and password and click “OK”.

Once you see the LED of mesh unit turns to solid green that means your mesh unit is successfully connected with the web.

Connect the secondary Brostrend nodes to the internet

Firstly notice your all node must be at high and at open territory.
Also ensure the wall in between any two nodes must be less than two.
And confirm that your node must be far from electronics. Example microwave oven, induction cooker and refrigerator.
Here use other power adapters to connectors to connect the left secondary nodes to wall socket; you will see LED light to solid green.
Now hold on 40 second and your secondary node is connected with another node then LED turn to flickers green.
Led status if you see the LED turns to solid green that means your connection is good. If your LED turns to solid yellow that means your connection is fair. If your LED turns to solid red that means you are disconnected.

Bros Trend Extender Setup

Post category:Bros Trend Extender Bros Trend Extender Setup
Post comments:0 Comments

Bros Trend AC1200 extender is a wireless Wi-Fi extender that helps in eliminating dead spots at your workplace. One can simply connect the extender with the existing network. It has the good class display design. It contain of numerous features that create this extender different.

This extender comes up with many attributes which are as follows:

Permanent Signal Connection.
Complete Signal Coverage.
Compatible with every sort of router.

You can locate a definite place just with the assist of the smart signal indicator. You can connect the extender through Graphical User Interface (GUI) or WPS connection. Bros Trend wireless extender supports the dual-band technology that is 2 GHz to 5 GHz. It has a warranty which is a good thing for customers. Let’s begin the Bros Trend Extender setup:

Firstly to begin the setup, you have the SSID and Wi-Fi password of the main router network. Then you require plugging in the re.brostrend.com to the working power outlet.
Then, joining the setup, open any internet browser in your device and search for the default IP address by typing 192.168.10.1 or re.brostrend.com
After that login by write admin as the password and after this the device will perform a scan for the networks accessible. Out of these networks, choose the main Wi-Fi network.
At last follow the guidance given on the page through which the extender will be connected to the router network successfully.

You can also call on the Technical Support helpline for further assistance.

This extender comes up with many attributes which are as follows:

Permanent Signal Connection.
Complete Signal Coverage.
Compatible with every sort of router.

You can locate a definite place just with the assist of the smart signal indicator. You can connect the extender through Graphical User Interface (GUI) or WPS connection. Bros Trend wireless extender supports the dual-band technology that is 2 GHz to 5 GHz. It has a warranty which is a good thing for customers. Let’s begin the Bros Trend Extender setup:

Firstly to begin the setup, you have the SSID and Wi-Fi password of the main router network. Then you require plugging in the re.brostrend.com to the working power outlet.
Then, joining the setup, open any internet browser in your device and search for the default IP address by typing 192.168.10.1 or re.brostrend.com
After that login by write admin as the password and after this the device will perform a scan for the networks accessible. Out of these networks, choose the main Wi-Fi network.
At last follow the guidance given on the page through which the extender will be connected to the router network successfully.

You can also call on the Technical Support helpline for further assistance.

Bros Trend Extender setup via WPS

Connect to the main router with the simple method to use the WPS button. This method uses the WPS button on the router and the Wi-Fi extender to quickly connect the two. Every router is different and not all routers are same or it may need to be turned on in the router settings.

WPS Setup Steps

Firstly, power on the unit and just hold up for the Power LED to turn blue.
Then, press the WPS button on the router.
After that press the WPS button on the Bros Trend AC1200.
Just hold up for the Signal LED to turn solid blue.
When it turns solid blue it is begin to use.

How to Connect to Router manually

On the off chance the WPS method above does not work for you logging into the unit manually can also be done.

Firstly, plug-in the unit powering it on
And open Wi-Fi settings and connect to BrosTrend_EXT
Then, open a Browser and write in 192.168.0.254
After that create a Password.
Find your router and select it.
After this enter the router Wi-Fi password.
It shows Extended Successfully!
At last you can log into the BrosTrend AC1200 on the 5G_EXT or 5G_5GEXT

Bros Trend Extender

Post category:Bros Trend Extender
Post comments:0 Comments

The Bros Trend Extender is greatly improving the wireless in a home. It can boost a wireless signal, be an access point, extend Wi-Fi, or add Wi-Fi to non-wireless devices. The Wi-Fi range extenders add an access point to a location or add Wi-Fi to an Ethernet-only device for example a smart TV of gaming console. It is a simple device built to assist improves or add Wi-Fi in many numerous wireless environments.

Features of Bros trend extender

Bros Trend Wi-Fi Range Extending Technology

Wi-Fi booster range extender boosts and conveys superior wireless signal coverage throughout your house. Also conveys good wireless range than Wi-Fi extenders with internal antennas.

Dedicated Network CPU Handles 1200Mbps Speed at Ease

Ideal for lag-free online HD video streaming, multi-users gaming, voice-calling, and browsing etc.

· Wi-Fi with 4 X Speed

It conveys 4 times speed as that of N300 or nearly 2 times as that of AC750, push your wireless range to the extreme without upgrading any existing equipment by adding this 1200Mbps dual band Wi-Fi booster.

· Works with Any Wi-Fi Routers

It has to connect any of your Wi-Fi devices to the extended Internet network, for example your smart phone, tablet, TV, game console, and streaming players etc

· WI-Fi Bridge – Connect Wired Device to Wi-Fi

Upgrade your wired entertainment device to AC Wi-Fi speed in a single shot with this dual band Wi-Fi extender booster.

· Access Point Mode – Create another Wi-Fi Network

It has use Ethernet cable to connect this Wi-Fi booster range extender to any Internet enabled Ethernet port in your room or Ethernet port of existing router; you can make a new AC1200 dual band wireless network.

It also has two small adjustable Wi-Fi antennas to get a better signal.

Firmware update of Bros Trend Extender

Firmware update of Bros Trendextender should be possible by login on the extender page. You can access the page using the IP address allotted by the router (Note- 192.168.0.254 or re.brostrend.com). On the off chance that if you don’t know how access the login page after installation. When you login on the Setup page you have to click on “Administration” option.

Firstly, under the Administration choose the option Firmware update.
And then you have to locate the file for latest Firmware on your PC.
After that click Install and it will take some minutes to upgrade the firmware.
During the Update your Bros trend extender will reboot, Ensure don’t turn of the power, or else there is chance of malfunction.

Note- Download the Bros trend Extender firmware from the official website.